© OnlineSecurity-ON, 2004-2019. All rights are reserved.
|Free Downloads||Glossary||Contact Us||Starforce Windows 7|
Deactivation of the protected application. End user manual.
If you are going to change your computer hardware or reinstall the operating system, it is probable that the activated application does not run after that. To solve the problem, our experts have developed the license transfer technology or Deactivation, so that you could use your application again, without losing one activation possibility. In this case it is not necessary for you to contact the publisher of the protected application.
The number of deactivations and reactivations is determined by the publisher of the protected application during the protection installation.
You can launch the deactivation procedure by one of the three methods:
The ‘deactivate’ link should be pressed in the displayed window (the Serial Number used to activate the application is indicated in this window by default) (see ’ link should be pressed in the displayed window (the used to activate the application is indicated in this window by default) (see Fig. 2).
In case the product deactivation and reactivation were performed previously, the Serial Number will be followed by the Deactivation Code (after a colon) that has been used for the reactivation.
After pressing ‘deactivate’ a window requesting deactivation confirmation is displayed (see ’ a window requesting deactivation confirmation is displayed (see Fig. 3).
Press “Deactivate”; the following message is displayed then (Fig. 4).
Confirm the application deactivation ("Yes" button).
Attention! The product is actually deactivated on the computer right after the deactivation confirmation, but not after obtaining the Deactivation Code. It is necessary to obtain this code only for the product reactivation.
If your computer is connected to the Internet, the application deactivation is performed automatically and a window with the Deactivation Code is displayed (Fig. 5). It is important to save this code to be able to reactivate the product later.
Press “OK” to complete the automatic deactivation process. The product will only be available after the reactivation.
If automatic deactivation failed or it is not provided by the publisher at all, or your computer is not connected to the Internet, a window suggesting manual deactivation appears. After pressing “Deactivate” in the deactivation confirmation window (see Fig. 3) the following window is displayed (Fig. 6). You can also switch to this window by pressing “other” link in the deactivation confirmation window (see Fig. 3).
Type the indicated Serial Number and Hardware Code in the corresponding fields in the End users section of the ProActive website (see Fig. 7).
Press the “Get Deactivation Code” button. You will obtain a Deactivation Code (see Fig. 8). Write down the code, so that afterwards you can use it along with the Serial Number to reactivate the application.
As with the activation, if the Internet is not available (neither your computer nor any computer hereabouts is connected to the Internet), you can transfer the obtained Hardware Code and Serial Number to the activation server by one of the methods that the product distributor has supported in the protection interface window, or in some accompanying document, and obtain the required Deactivation Code.
As mentioned above, the application is actually deactivated on the computer right after the deactivation confirmation. If you could not complete the process after that for some reason, you can repeat the process to obtain the Deactivation Code. The same should be done to obtain the Deactivation Code once more, if it was lost before you could use for reactivation.
To do so, launch the application deactivation once more using one of the described methods. After the deactivation confirmation a window requesting the repeated deactivation confirmation is displayed (see Fig. 9).
After the confirmation, the above-mentioned process to obtain the Deactivation Code begins.
The reactivation method is determined in the same way as for usual activation
The process of automatic reactivation is similar to the automatic activation except one thing: the Deactivation Code should be typed in after the Serial Number and a colon in the corresponding edit box.
Attention! In case it is not the first time the license has been transferred on this computer, the Deactivation Code of the previous deactivation is displayed in the Serial Number field after a colon. This code should be replaced with the code generated during the last deactivation.
Manual reactivation is similar to manual activation: go to the specified activation website and enter the Serial Number, the Hardware Code and the Deactivation Code to the corresponding fields. After pressing “Get Activation Key” you will obtain an Activation Key to reactivate and run your application.
* Besides the Serial Number and the Hardware Code, NO personal data are sent to the StarForce activation server during the automatic activation/deactivation.
Print this page